Jump to content

Repairing the belt loop on a knife scabbard


Daniel

Recommended Posts

So Rock Hall's tomorrow, and I find the belt loop on the scabbard for the beautiful knife I bought at Lockhouse last year is broken.

The scabbard is a single piece of leather folded and stitched together along the edge. The belt loop is a simple strip of leather stitched at each end through the side of the scabbard. It's the end closer to the scabbard's point, the non-load-bearing end, that's come unstitched. Obviously, when the scabbard was made, the belt loop was stitched on first, and only afterward was the scabbard folded and stitched together. There's no way anyone could have poked a needle down into the scabbard after it was finished to stitch the belt loop on, and no way that I can do it now.

What would a pirate do in this situation? Maybe just forget about the belt loop and tuck the silly scabbard inside his belt. But what I did was take a strip of linen about 3/4 inch by10 inches, and stitch through the middle of it into the holes on the inner side of the lower end of the belt loop, then wrapped the ends around the other side of the scabbard and tied them tightly with two reef knots. Voila, a working belt loop again! It looks like hell, but I imagine real pirates' equipment might often have quite a jury-rigged appearance.

Any one know how repairs like this were actually done in period? I can't imagine that any period source would talk about this, but maybe some archaeologist turned up a a repaired scabbard at some point?

Scabbardrepair2.jpg

Inner side of the repaired scabbard, with lower end of

belt loop stitched to linen strip between belt loop and

scabbard.

Scabbardrepair1.jpg

Linen strip secured on outer side of scabbard with

double reef knots, holding belt loop in place.

Link to comment
Share on other sites

Thanks! I don't own a curved needle, so never thought of using one, but it would probably be easy to find and acquire. The holes are so close together that I don't think I could stitch from one hole into an adjacent one, but I could just stitch every second or third hole, and stitch the holes I missed the first time when I came around the second or third time.

I don't believe I would want to unstitch the scabbard edge; the stitched edge is finished with some kind of black glue or sealant that I don't think I could replace.

Link to comment
Share on other sites

Daniel -

You could also try to rivet the bottom of the belt loop.

Cut a small hole in the backside of the sheath and the loop. Slide a rivet into the sheath and through the hole you made in the back. Use a piece of steel slid into the sheath as an anvil and set the rivet.

Also what you did with the linen... try it with a piece of leather, similar to a keeper loop on your belt.

"Born on an island, live on an island... the sea has always been in my blood." Jas. Hook

"You can't direct the wind . . . but . . . you can adjust the sails."

"Don't eat the chickens with writing on their beaks." Governor Sawney

Link to comment
Share on other sites

Love it! Has a "castaway" look!

Jib, it does at that.

Arrrrgh... The only other option would be to carry it around in your teeth. :rolleyes::D

"Born on an island, live on an island... the sea has always been in my blood." Jas. Hook

"You can't direct the wind . . . but . . . you can adjust the sails."

"Don't eat the chickens with writing on their beaks." Governor Sawney

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...
&ev=PageView&cd%5Bitem_id%5D=19381&cd%5Bitem_name%5D=Repairing+the+belt+loop+on+a+knife+scabbard&cd%5Bitem_type%5D=topic&cd%5Bcategory_name%5D=Crafting Kit"/>