Jump to content

Question regarding glazed linen


Yellowbeard

Recommended Posts

I've seen late 18th century cocked hats made of beaver felt that were covered with 'glazed linen' to waterproof them to a certain extent. I've been looking around the interwebtubes for a source for the stuff and all I've seen is material for furniture and doesn't look at all right, plus it's wicked expensive at almost $100 a yard.

So, if anyone knows what I'm on about, is there a technique I can use to treat regular old linen to get the same effect?

Link to comment
Share on other sites

sorry double posted see following post

Edited by Capt. Sterling


"I being shot through the left cheek, the bullet striking away great part of my upper jaw, and several teeth which dropt down the deck where I fell... I was forced to write what I would say to prevent the loss of blood, and because of the pain I suffered by speaking."~ Woodes Rogers

Crewe of the Archangel

http://jcsterlingcptarchang.wix.com/creweofthearchangel#

http://creweofthearchangel.wordpress.com/

Link to comment
Share on other sites

Glazed Fabric:

A material to which a gloss has been applied by means of treatment with paraffin then passage through heated rollers...

The Encyclopedia of World Costume

Glazing

Glazing is a textile finish that adds luster and smoothness to the surface of the fabric. Many glazed fabrics are plain-woven cotton. A specialized calender (set of metal rollers) called a friction calender, literally rubs the fabric lustrous. Glazed chintz and polished cotton are examples of glazed fabrics.

The Process

The fabric is first impregnated with wax, starch, or a resin solution using a pad machine. The fabric passes through the solution in a bath, then through pad rollers. Pressure is applied so that the solution is forced into the fabric. The pressure on the pad roller squeezes the excess solution out of the fabric. The fabric is partially dried and passed through a friction calender. The friction calender is made up of three rollers. One roller is a padded roller that moves the fabric slowly between two metal rollers. As the fabric moves slowly between the rapidly moving heated metal rollers, the friction creates heat. The fast moving metal rollers polish the fabric. The glaze will be temporary if the fabric has been treated with wax or starch. The finish will be durable if the fabric has been treated with resins. The glazing will be durable on thermoplastic (heat sensitive) fiber fabrics because the friction rollers produce heat.

Cire

A specialized finish, cireing (sometimes called the “wet look”) is similar to glazing. The difference is that very hot rollers in the friction calender are used to add a highly lustrous surface. Again, waxes, starches, or thermoplastic resins are added to the fabric. When thermoplastic fibers are used in the cire process the fibers slightly fuse, melt, and flatten. The cire finish on thermoplastic fibers is permanent. When hydrophobic fiber fabrics are given a cire finish the resultant fabric is water repellent. Typical fabrics that are cired are taffeta (a filament unbalanced ribbed fabric), tricot (a warp knit), and satin.

Glazing can occur accidentally when fabrics are over-pressed. Glazing occurs when a too hot iron is used on a fabric made from a fiber that is heat sensitive. The heat is not enough to melt the fabric completely but does slightly fuse and flatten the fibers. An undesirable sheen that may resemble an oil stain will appear. The damage will be permanent.

Another definition for glazing is the pressing of fur to develop a desirable sheen. The pressing aligns the hairs in the fur, thus generating a natural luster and additional softness to the fur. Often a glazing solution using a spray gun is applied.

BIBLIOGRAPHY

Needles, Howard L. Textile Fibers, Dyes, Finishes, and Process: A Concise Guide. Park Ridge, N.J.: Noyes Publications, 1986.

Slade, Philip E. Handbook of Fiber Finish Technology. New York: Marcel Dekker, 1998.

From The Clothing and Fashion Encyclopedia

Do you mean a hat cover made of glazed linen? and not some sort of treatment added directly to the beaver hat?


"I being shot through the left cheek, the bullet striking away great part of my upper jaw, and several teeth which dropt down the deck where I fell... I was forced to write what I would say to prevent the loss of blood, and because of the pain I suffered by speaking."~ Woodes Rogers

Crewe of the Archangel

http://jcsterlingcptarchang.wix.com/creweofthearchangel#

http://creweofthearchangel.wordpress.com/

Link to comment
Share on other sites

Thanks for the reply Capt.Sterling. as I feared, it sounds WAAAY to complex for me to attempt in my garage!

And yes, it was a permanent covering on the hat- i have a picture and description of one in a book, I'll scan it and post it at work tomorrow so you can see what I'm on about.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...